According to Safe Work Australia, there were 147,200 serious claims of workers’ compensation in 2024-25. All of them include at least one week of loss of work time. There are 21,500 of them involving cuts, wounds, amputations or harm to internal organs. The statistics include all industries and do not include injuries from flaring. Nevertheless, there are similar risks associated with using pipe flaring tools.
Choosing The Tool For The Tube
It is important to evaluate the tube first rather than choose the pipe flaring tool. Its diameter, wall thickness and type of measurement system (imperial or metric) will define the list of possible tools. The majority of flaring kits designed for air conditioning purposes produce 45-degree flares. Make sure that the chosen kit works well with the existing fittings before purchasing.
A simple yoke tool will work well for occasional use. An eccentric cone will need less force when working with a large-diameter tube, whereas self-aligning the bar ensures better straight positioning of the tube in the block. There are powered tools designed to repeat the same task throughout the day.
It is necessary to check the range of tube sizes that is appropriate for the tool. Otherwise, it will not be used in the van. It is possible to find information about suitable sizes and materials of the tube in the manufacturer’s instructions.
Why Finishing Matters?
The cone face, holes in the bar and yoke alignment are responsible for the evenness and circular form of the finished flare. Improper machining will result in marks on the tool, which will become marks on the tube itself. Parts of the tool deteriorate over time, and the cone, which was able to produce even surfaces of copper, will eventually leave marks.

Oval flares and marks on the cone indicate a possible failure of the joint. The comparison of different brands is not included in this article, since no tools have been evaluated. It is cheaper to replace the cone than visit the customer again.
Where Injuries Occur All Too Often?
Traumatic joint, ligament, muscle and tendon injuries made up a whopping 36.6 per cent of serious claims; that’s a staggering 53,900 cases. And then there are the wounds and lacerations, which accounted for a further 14.6 per cent, a nasty reminder of the dangers faced by people in the workshop. One of the main culprits is a fresh tube end which can suddenly slash a person’s hand, while a stiff feed screw can start to strain the wrist after hours of repetitive work at the bench.
Safe Work Australia recorded a tragic 222 traumatic worker deaths in 2025, the highest annual figure since 2012. We’re looking at provisional data which covers all workplaces, so it doesn’t establish any direct link with flaring injuries. What it does show is why workers need to take the simple precautions of removing burrs from tube ends, securing that clamp and using a steady hand.
Getting The Flare Right From The Start
To create a clean flare, you first need to cut the tube square and get rid of any burrs on both the inside and outside edges. Then slide the flare nut onto the tube before you shape the cone. Just follow the tool’s instructions and set the tube projection at the right height, then, and this is important, clamp it firmly and turn the feed screw slowly and in a steady, even motion.
A lot of instruction sheets will tell you to put a tiny drop of oil on the cone to help things move smoothly. But don’t rush it; if you work too quickly you’re liable to split the rim of the flare and end up with something that’s useless. That extra minute to get it right is a small price to pay compared to dealing with a leak.
Checking Out Your Finished Flare
So, what makes a good flare? Well, it should have a smooth, even sealing surface, no nasty radial scratches and a uniform wall right around the full circumference. If there are any cracks at the rim, it may be a sign that you’ve been working the metal a bit too hard or, worse still, you’ve been turning the tool too quickly. And if your flare is a bit too big or a bit too small, it may cause problems later on.
Take a good look at that flare under nice bright lighting and give it a slow turn to check out the whole surface. If it looks a bit uneven, I’m afraid it’s unlikely to perform any better once it’s installed. If in doubt, just cut it off and remake it rather than trying to fix it by tightening the fitting even harder.
A Trades Market In Short Supply Of Skilled Workers
Jobs and Skills Australia found that 279 occupations are in short supply in 2026; that’s a massive 27 per cent of the occupations they assessed. And it’s not just any old occupation; nearly half of the Technicians and Trades Workers are in short supply, and a whopping 127 occupations have been in shortage every year from 2021 to 2026. The data doesn’t say anything about workshop supervision, so we can’t draw a direct line between shortage and flaring quality. But here’s the thing: a busy trade has even less room for error, making that extra minute spent on the first flare really worthwhile.
Keeping Your Tool In Top Nick
When you’ve finished the job, remember to clear out all the filings and oil from the tool. If you don’t, you risk scratching the next flare you make with all sorts of dirt and metal particles. Give the cone, yoke and feed screw a regular check too, and if they’re showing signs of wear, just replace them instead of trying to carry on with a worn tool. And please, for goodness’ sake, don’t use this tool as a hammer, pry bar or clamp for other work! Keep it for flaring only. Before you start the next job, make sure to secure the bench vice and then position the tube; that’s the way to get the best possible results.